![]() ![]() Additional scenarios/default ones can be modified using Teltonika Configurator. Note! This table contains only the default scenarios. Table 3 User interface LED indication scenarios SCENARIO INDICATION MEANING GSM error Red LED 500 ms blink 3 times + Buzzer SIM is not inserted, the device can’t connect to the operator, or the GSM signal is being jammed No GNSS fix Red LED 1000 ms blink 1 time The device doesn’t have valid GNSS fix and is searching for coordinates GNSS fix Green LED 1000 ms blink 1 time The device has a valid GNSS fix Key pressed 1000 ms interval Buzzer while active Key is pressed and held Private Trip Green LED 500 ms blink 3 times +īuzzer The battery is almost fully discharged Business Trip Blue LED 500 ms blink 3 times + Buzzer The indication is used to remind the user that the device is still operational Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters. Records sending to server: If the device has made a record it is sent to the server every 120 secondsĪfter successful SMS configuration, the FMP100 device will synchronize time and update records to configured server. Meters Speed difference between last coordinate and current position is greater than 10 km/hĭevice makes a record On Stop if: 1-hour passes while the vehicle is stationary and ignition is off Movement and ignition detection: Vehicle movement will be detected by accelerometer Ignition will be detected by the vehicle power voltage between 13,2 – 30 Vĭevice makes a record On Moving if one of these events happen: 300 seconds pass Vehicle turns 10 degrees Vehicle drives 100 2006 – Data sending protocol (0 – TCP, 1 – UDP).2003 – APN password (if there are no APN password, empty field should be left).2002 – APN username (if there are no APN username, empty field should be left).Note: Before SMS text, two space symbols should be inserted. Quickly set up your device by sending this SMS command to it: Quick SMS configurationĭefault configuration has optimal parameters present to ensure the best performance of track quality and data usage. More details about FMP100 configuration using Configurator can be found in our Wiki. The most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured. Reset configuration – sets device configuration to default. Read records – reads records from the device. Update firmware – updates the firmware on the device. Save to file – saves the configuration to file. Load from file – loads configuration from file. Save to device – saves the configuration to the device. Main buttons offer the following functionality: Load from the device – loads configuration from the device. FMP100 has one user-editable modification of configuration the changes need to be saved to the device using the Save to devise button. Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. The configuration process begins by pressing on a connected device (Figure 6 Device connected via Bluetooth).Īfter connection to Configurator Status window will be displayed (Figure 7 Configurator Status window). After launch software language can be changed by clicking in the right bottom corner ( Figure 5 Language selection). NET Framework4.6.2 32 and 64 bit Downloaded Configurator will be in a compressed archive. NET Framework version Version Links Windows Vista Make sure you have the correct version installed. Configurator operates on Microsoft Windows OS and uses the prerequisite MS. Get the latest Configurator version from here. ![]() The main configuration can be performed via Teltonika Configurator software. These settings should be changed according to the user’s needs. Configuration (Windows)Īt first FMP100 device will have the default factory settings set. If Bluetooth connection is not possible, please refer to the FMP100 Wiki page on how to open the device casing and connect it via Micro-USB. Choose your device named – “FMBxxx_last_7_imei_digits”, without LE in the end.Įnter default password 5555, press Connect, and then select Done. Turn on Bluetooth on your PC, then select Add Bluetooth or another device> Bluetooth. FMP100 Bluetooth is enabled by default.LEDs should start blinking, see “Error! Reference source not found.”. Power-up FMP100 with DC voltage (12 – 30 V) power supply.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |